In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Clear Present bit before tearing down context entry
When tearing down a context entry, the current implementation zeros the
entire 128-bit entry using multiple 64-bit writes. This creates a window
where the hardware can fetch a "torn" entry — where some fields are
already zeroed while the 'Present' bit is still set — leading to
unpredictable behavior or spurious faults.
While x86 provides strong write ordering, the compiler may reorder writes
to the two 64-bit halves of the context entry. Even without compiler
reordering, the hardware fetch is not guaranteed to be atomic with
respect to multiple CPU writes.
Align with the "Guidance to Software for Invalidations" in the VT-d spec
(Section 6.5.3.3) by implementing the recommended ownership handshake:
1. Clear only the 'Present' (P) bit of the context entry first to
signal the transition of ownership from hardware to software.
2. Use dma_wmb() to ensure the cleared bit is visible to the IOMMU.
3. Perform the required cache and context-cache invalidation to ensure
hardware no longer has cached references to the entry.
4. Fully zero out the entry only after the invalidation is complete.
Also, add a dma_wmb() to context_set_present() to ensure the entry
is fully initialized before the 'Present' bit becomes visible.
In the Linux kernel, the following vulnerability has been resolved:
erofs: fix inline data read failure for ztailpacking pclusters
Compressed folios for ztailpacking pclusters must be valid before adding
these pclusters to I/O chains. Otherwise, z_erofs_decompress_pcluster()
may assume they are already valid and then trigger a NULL pointer
dereference.
It is somewhat hard to reproduce because the inline data is in the same
block as the tail of the compressed indexes, which are usually read just
before. However, it may still happen if a fatal signal arrives while
read_mapping_folio() is running, as shown below:
erofs: (device dm-1): z_erofs_pcluster_begin: failed to get inline data -4
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
...
pc : z_erofs_decompress_queue+0x4c8/0xa14
lr : z_erofs_decompress_queue+0x160/0xa14
sp : ffffffc08b3eb3a0
x29: ffffffc08b3eb570 x28: ffffffc08b3eb418 x27: 0000000000001000
x26: ffffff8086ebdbb8 x25: ffffff8086ebdbb8 x24: 0000000000000001
x23: 0000000000000008 x22: 00000000fffffffb x21: dead000000000700
x20: 00000000000015e7 x19: ffffff808babb400 x18: ffffffc089edc098
x17: 00000000c006287d x16: 00000000c006287d x15: 0000000000000004
x14: ffffff80ba8f8000 x13: 0000000000000004 x12: 00000006589a77c9
x11: 0000000000000015 x10: 0000000000000000 x9 : 0000000000000000
x8 : 0000000000000000 x7 : 0000000000000000 x6 : 000000000000003f
x5 : 0000000000000040 x4 : ffffffffffffffe0 x3 : 0000000000000020
x2 : 0000000000000008 x1 : 0000000000000000 x0 : 0000000000000000
Call trace:
z_erofs_decompress_queue+0x4c8/0xa14
z_erofs_runqueue+0x908/0x97c
z_erofs_read_folio+0x128/0x228
filemap_read_folio+0x68/0x128
filemap_get_pages+0x44c/0x8b4
filemap_read+0x12c/0x5b8
generic_file_read_iter+0x4c/0x15c
do_iter_readv_writev+0x188/0x1e0
vfs_iter_read+0xac/0x1a4
backing_file_read_iter+0x170/0x34c
ovl_read_iter+0xf0/0x140
vfs_read+0x28c/0x344
ksys_read+0x80/0xf0
__arm64_sys_read+0x24/0x34
invoke_syscall+0x60/0x114
el0_svc_common+0x88/0xe4
do_el0_svc+0x24/0x30
el0_svc+0x40/0xa8
el0t_64_sync_handler+0x70/0xbc
el0t_64_sync+0x1bc/0x1c0
Fix this by reading the inline data before allocating and adding
the pclusters to the I/O chains.
In the Linux kernel, the following vulnerability has been resolved:
ext4: fix e4b bitmap inconsistency reports
A bitmap inconsistency issue was observed during stress tests under
mixed huge-page workloads. Ext4 reported multiple e4b bitmap check
failures like:
ext4_mb_complex_scan_group:2508: group 350, 8179 free clusters as
per group info. But got 8192 blocks
Analysis and experimentation confirmed that the issue is caused by a
race condition between page migration and bitmap modification. Although
this timing window is extremely narrow, it is still hit in practice:
folio_lock ext4_mb_load_buddy
__migrate_folio
check ref count
folio_mc_copy __filemap_get_folio
folio_try_get(folio)
......
mb_mark_used
ext4_mb_unload_buddy
__folio_migrate_mapping
folio_ref_freeze
folio_unlock
The root cause of this issue is that the fast path of load_buddy only
increments the folio's reference count, which is insufficient to prevent
concurrent folio migration. We observed that the folio migration process
acquires the folio lock. Therefore, we can determine whether to take the
fast path in load_buddy by checking the lock status. If the folio is
locked, we opt for the slow path (which acquires the lock) to close this
concurrency window.
Additionally, this change addresses the following issues:
When the DOUBLE_CHECK macro is enabled to inspect bitmap-related
issues, the following error may be triggered:
corruption in group 324 at byte 784(6272): f in copy != ff on
disk/prealloc
Analysis reveals that this is a false positive. There is a specific race
window where the bitmap and the group descriptor become momentarily
inconsistent, leading to this error report:
ext4_mb_load_buddy ext4_mb_load_buddy
__filemap_get_folio(create|lock)
folio_lock
ext4_mb_init_cache
folio_mark_uptodate
__filemap_get_folio(no lock)
......
mb_mark_used
mb_mark_used_double
mb_cmp_bitmaps
mb_set_bits(e4b->bd_bitmap)
folio_unlock
The original logic assumed that since mb_cmp_bitmaps is called when the
bitmap is newly loaded from disk, the folio lock would be sufficient to
prevent concurrent access. However, this overlooks a specific race
condition: if another process attempts to load buddy and finds the folio
is already in an uptodate state, it will immediately begin using it without
holding folio lock.
In the Linux kernel, the following vulnerability has been resolved:
tpm: tpm_i2c_infineon: Fix locality leak on get_burstcount() failure
get_burstcount() can return -EBUSY on timeout. When this happens, the
function returns directly without releasing the locality that was
acquired at the beginning of tpm_tis_i2c_send().
Use goto out_err to ensure proper cleanup when get_burstcount() fails.
In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: fix oops when split header is enabled
For GMAC4, when split header is enabled, in some rare cases, the
hardware does not fill buf2 of the first descriptor with payload.
Thus we cannot assume buf2 is always fully filled if it is not
the last descriptor. Otherwise, the length of buf2 of the second
descriptor will be calculated wrong and cause an oops:
Unable to handle kernel paging request at virtual address ffff00019246bfc0
...
x2 : 0000000000000040 x1 : ffff00019246bfc0 x0 : ffff00009246c000
Call trace:
dcache_inval_poc+0x28/0x58 (P)
dma_direct_sync_single_for_cpu+0x38/0x6c
__dma_sync_single_for_cpu+0x34/0x6c
stmmac_napi_poll_rx+0x8f0/0xb60
__napi_poll.constprop.0+0x30/0x144
net_rx_action+0x160/0x274
handle_softirqs+0x1b8/0x1fc
...
To fix this, the PL bit-field in RDES3 register is used for all
descriptors, whether it is the last descriptor or not.
In the Linux kernel, the following vulnerability has been resolved:
gpib: Fix memory leak in ni_usb_init()
In ni_usb_init(), if ni_usb_setup_init() fails, the function returns
-EFAULT without freeing the allocated writes buffer, leading to a
memory leak.
Additionally, ni_usb_setup_init() returns 0 on failure, which causes
ni_usb_init() to return -EFAULT, an inappropriate error code for this
situation.
Fix the leak by freeing writes in the error path. Modify
ni_usb_setup_init() to return -EINVAL on failure and propagate this
error code in ni_usb_init().
In the Linux kernel, the following vulnerability has been resolved:
power: supply: pm8916_lbc: Fix use-after-free in power_supply_changed()
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle.
In the Linux kernel, the following vulnerability has been resolved:
crypto: inside-secure/eip93 - fix kernel panic in driver detach
During driver detach, the same hash algorithm is unregistered multiple
times due to a wrong iterator.
In the Linux kernel, the following vulnerability has been resolved:
power: supply: goldfish: Fix use-after-free in power_supply_changed()
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle.
In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: Fix slab-out-of-bounds read in DeleteIndexEntryRoot
In the 'DeleteIndexEntryRoot' case of the 'do_action' function, the
entry size ('esize') is retrieved from the log record without adequate
bounds checking.
Specifically, the code calculates the end of the entry ('e2') using:
e2 = Add2Ptr(e1, esize);
It then calculates the size for memmove using 'PtrOffset(e2, ...)',
which subtracts the end pointer from the buffer limit. If 'esize' is
maliciously large, 'e2' exceeds the used buffer size. This results in
a negative offset which, when cast to size_t for memmove, interprets
as a massive unsigned integer, leading to a heap buffer overflow.
This commit adds a check to ensure that the entry size ('esize') strictly
fits within the remaining used space of the index header before performing
memory operations.
In the Linux kernel, the following vulnerability has been resolved:
bpf: Preserve id of register in sync_linked_regs()
sync_linked_regs() copies the id of known_reg to reg when propagating
bounds of known_reg to reg using the off of known_reg, but when
known_reg was linked to reg like:
known_reg = reg ; both known_reg and reg get same id
known_reg += 4 ; known_reg gets off = 4, and its id gets BPF_ADD_CONST
now when a call to sync_linked_regs() happens, let's say with the following:
if known_reg >= 10 goto pc+2
known_reg's new bounds are propagated to reg but now reg gets
BPF_ADD_CONST from the copy.
This means if another link to reg is created like:
another_reg = reg ; another_reg should get the id of reg but
assign_scalar_id_before_mov() sees
BPF_ADD_CONST on reg and assigns a new id to it.
As reg has a new id now, known_reg's link to reg is broken. If we find
new bounds for known_reg, they will not be propagated to reg.
This can be seen in the selftest added in the next commit:
0: (85) call bpf_get_prandom_u32#7 ; R0=scalar()
1: (57) r0 &= 255 ; R0=scalar(smin=smin32=0,smax=umax=smax32=umax32=255,var_off=(0x0; 0xff))
2: (bf) r1 = r0 ; R0=scalar(id=1,smin=smin32=0,smax=umax=smax32=umax32=255,var_off=(0x0; 0xff)) R1=scalar(id=1,smin=smin32=0,smax=umax=smax32=umax32=255,var_off=(0x0; 0xff))
3: (07) r1 += 4 ; R1=scalar(id=1+4,smin=umin=smin32=umin32=4,smax=umax=smax32=umax32=259,var_off=(0x0; 0x1ff))
4: (a5) if r1 < 0xa goto pc+4 ; R1=scalar(id=1+4,smin=umin=smin32=umin32=10,smax=umax=smax32=umax32=259,var_off=(0x0; 0x1ff))
5: (bf) r2 = r0 ; R0=scalar(id=2,smin=umin=smin32=umin32=6,smax=umax=smax32=umax32=255) R2=scalar(id=2,smin=umin=smin32=umin32=6,smax=umax=smax32=umax32=255)
6: (a5) if r1 < 0xe goto pc+2 ; R1=scalar(id=1+4,smin=umin=smin32=umin32=14,smax=umax=smax32=umax32=259,var_off=(0x0; 0x1ff))
7: (35) if r0 >= 0xa goto pc+1 ; R0=scalar(id=2,smin=umin=smin32=umin32=6,smax=umax=smax32=umax32=9,var_off=(0x0; 0xf))
8: (37) r0 /= 0
div by zero
When 4 is verified, r1's bounds are propagated to r0 but r0 also gets
BPF_ADD_CONST (bug).
When 5 is verified, r0 gets a new id (2) and its link with r1 is broken.
After 6 we know r1 has bounds [14, 259] and therefore r0 should have
bounds [10, 255], therefore the branch at 7 is always taken. But because
r0's id was changed to 2, r1's new bounds are not propagated to r0.
The verifier still thinks r0 has bounds [6, 255] before 7 and execution
can reach div by zero.
Fix this by preserving id in sync_linked_regs() like off and subreg_def.
In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix tcx/netkit detach permissions when prog fd isn't given
This commit fixes a security issue where BPF_PROG_DETACH on tcx or
netkit devices could be executed by any user when no program fd was
provided, bypassing permission checks. The fix adds a capability
check for CAP_NET_ADMIN or CAP_SYS_ADMIN in this case.
In the Linux kernel, the following vulnerability has been resolved:
accel/amdxdna: Hold mm structure across iommu_sva_unbind_device()
Some tests trigger a crash in iommu_sva_unbind_device() due to
accessing iommu_mm after the associated mm structure has been
freed.
Fix this by taking an explicit reference to the mm structure
after successfully binding the device, and releasing it only
after the device is unbound. This ensures the mm remains valid
for the entire SVA bind/unbind lifetime.
In the Linux kernel, the following vulnerability has been resolved:
net: mctp: ensure our nlmsg responses are initialised
Syed Faraz Abrar (@farazsth98) from Zellic, and Pumpkin (@u1f383) from
DEVCORE Research Team working with Trend Micro Zero Day Initiative
report that a RTM_GETNEIGH will return uninitalised data in the pad
bytes of the ndmsg data.
Ensure we're initialising the netlink data to zero, in the link, addr
and neigh response messages.
In the Linux kernel, the following vulnerability has been resolved:
ovpn: fix possible use-after-free in ovpn_net_xmit
When building the skb_list in ovpn_net_xmit, skb_share_check will free
the original skb if it is shared. The current implementation continues
to use the stale skb pointer for subsequent operations:
- peer lookup,
- skb_dst_drop (even though all segments produced by skb_gso_segment
will have a dst attached),
- ovpn_peer_stats_increment_tx.
Fix this by moving the peer lookup and skb_dst_drop before segmentation
so that the original skb is still valid when used. Return early if all
segments fail skb_share_check and the list ends up empty.
Also switch ovpn_peer_stats_increment_tx to use skb_list.next; the next
patch fixes the stats logic.
In the Linux kernel, the following vulnerability has been resolved:
media: chips-media: wave5: Fix memory leak on codec_info allocation failure
In wave5_vpu_open_enc() and wave5_vpu_open_dec(), a vpu instance is
allocated via kzalloc(). If the subsequent allocation for inst->codec_info
fails, the functions return -ENOMEM without freeing the previously
allocated instance, causing a memory leak.
Fix this by calling kfree() on the instance in this error path to ensure
it is properly released.
In the Linux kernel, the following vulnerability has been resolved:
bpf: Require frozen map for calculating map hash
Currently, bpf_map_get_info_by_fd calculates and caches the hash of the
map regardless of the map's frozen state.
This leads to a TOCTOU bug where userspace can call
BPF_OBJ_GET_INFO_BY_FD to cache the hash and then modify the map
contents before freezing.
Therefore, a trusted loader can be tricked into verifying the stale hash
while loading the modified contents.
Fix this by returning -EPERM if the map is not frozen when the hash is
requested. This ensures the hash is only generated for the final,
immutable state of the map.
In the Linux kernel, the following vulnerability has been resolved:
rust: pwm: Fix potential memory leak on init error
When initializing a PWM chip using pwmchip_alloc(), the allocated device
owns an initial reference that must be released on all error paths.
If __pinned_init() were to fail, the allocated pwm_chip would currently
leak because the error path returns without calling pwmchip_put().
In the Linux kernel, the following vulnerability has been resolved:
thermal/of: Fix reference leak in thermal_of_cm_lookup()
In thermal_of_cm_lookup(), tr_np is obtained via of_parse_phandle(), but
never released.
Use the __free(device_node) cleanup attribute to automatically release
the node and fix the leak.
[ rjw: Changelog edits ]
In the Linux kernel, the following vulnerability has been resolved:
ksmbd: call ksmbd_vfs_kern_path_end_removing() on some error paths
There are two places where ksmbd_vfs_kern_path_end_removing() needs to be
called in order to balance what the corresponding successful call to
ksmbd_vfs_kern_path_start_removing() has done, i.e. drop inode locks and
put the taken references. Otherwise there might be potential deadlocks
and unbalanced locks which are caught like:
BUG: workqueue leaked lock or atomic: kworker/5:21/0x00000000/7596
last function: handle_ksmbd_work
2 locks held by kworker/5:21/7596:
#0: ffff8881051ae448 (sb_writers#3){.+.+}-{0:0}, at: ksmbd_vfs_kern_path_locked+0x142/0x660
#1: ffff888130e966c0 (&type->i_mutex_dir_key#3/1){+.+.}-{4:4}, at: ksmbd_vfs_kern_path_locked+0x17d/0x660
CPU: 5 PID: 7596 Comm: kworker/5:21 Not tainted 6.1.162-00456-gc29b353f383b #138
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-debian-1.17.0-1 04/01/2014
Workqueue: ksmbd-io handle_ksmbd_work
Call Trace:
<TASK>
dump_stack_lvl+0x44/0x5b
process_one_work.cold+0x57/0x5c
worker_thread+0x82/0x600
kthread+0x153/0x190
ret_from_fork+0x22/0x30
</TASK>
Found by Linux Verification Center (linuxtesting.org).
In the Linux kernel, the following vulnerability has been resolved:
net: usb: catc: enable basic endpoint checking
catc_probe() fills three URBs with hardcoded endpoint pipes without
verifying the endpoint descriptors:
- usb_sndbulkpipe(usbdev, 1) and usb_rcvbulkpipe(usbdev, 1) for TX/RX
- usb_rcvintpipe(usbdev, 2) for interrupt status
A malformed USB device can present these endpoints with transfer types
that differ from what the driver assumes.
Add a catc_usb_ep enum for endpoint numbers, replacing magic constants
throughout. Add usb_check_bulk_endpoints() and usb_check_int_endpoints()
calls after usb_set_interface() to verify endpoint types before use,
rejecting devices with mismatched descriptors at probe time.
Similar to
- commit 90b7f2961798 ("net: usb: rtl8150: enable basic endpoint checking")
which fixed the issue in rtl8150.
In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx5: Fix memory leak in GET_DATA_DIRECT_SYSFS_PATH handler
The UVERBS_HANDLER(MLX5_IB_METHOD_GET_DATA_DIRECT_SYSFS_PATH) function
allocates memory for the device path using kobject_get_path(). If the
length of the device path exceeds the output buffer length, the function
returns -ENOSPC but does not free the allocated memory, resulting in a
memory leak.
Add a kfree() call to the error path to ensure the allocated memory is
properly freed.
Compile tested only. Issue found using a prototype static analysis tool
and code review.
In the Linux kernel, the following vulnerability has been resolved:
mtd: parsers: Fix memory leak in mtd_parser_tplink_safeloader_parse()
The function mtd_parser_tplink_safeloader_parse() allocates buf via
mtd_parser_tplink_safeloader_read_table(). If the allocation for
parts[idx].name fails inside the loop, the code jumps to the err_free
label without freeing buf, leading to a memory leak.
Fix this by freeing the temporary buffer buf in the err_free label.
Compile tested only. Issue found using a prototype static analysis tool
and code review.
In the Linux kernel, the following vulnerability has been resolved:
ext4: fix dirtyclusters double decrement on fs shutdown
fstests test generic/388 occasionally reproduces a warning in
ext4_put_super() associated with the dirty clusters count:
WARNING: CPU: 7 PID: 76064 at fs/ext4/super.c:1324 ext4_put_super+0x48c/0x590 [ext4]
Tracing the failure shows that the warning fires due to an
s_dirtyclusters_counter value of -1. IOW, this appears to be a
spurious decrement as opposed to some sort of leak. Further tracing
of the dirty cluster count deltas and an LLM scan of the resulting
output identified the cause as a double decrement in the error path
between ext4_mb_mark_diskspace_used() and the caller
ext4_mb_new_blocks().
First, note that generic/388 is a shutdown vs. fsstress test and so
produces a random set of operations and shutdown injections. In the
problematic case, the shutdown triggers an error return from the
ext4_handle_dirty_metadata() call(s) made from
ext4_mb_mark_context(). The changed value is non-zero at this point,
so ext4_mb_mark_diskspace_used() does not exit after the error
bubbles up from ext4_mb_mark_context(). Instead, the former
decrements both cluster counters and returns the error up to
ext4_mb_new_blocks(). The latter falls into the !ar->len out path
which decrements the dirty clusters counter a second time, creating
the inconsistency.
To avoid this problem and simplify ownership of the cluster
reservation in this codepath, lift the counter reduction to a single
place in the caller. This makes it more clear that
ext4_mb_new_blocks() is responsible for acquiring cluster
reservation (via ext4_claim_free_clusters()) in the !delalloc case
as well as releasing it, regardless of whether it ends up consumed
or returned due to failure.
In the Linux kernel, the following vulnerability has been resolved:
sched/rt: Skip currently executing CPU in rto_next_cpu()
CPU0 becomes overloaded when hosting a CPU-bound RT task, a non-CPU-bound
RT task, and a CFS task stuck in kernel space. When other CPUs switch from
RT to non-RT tasks, RT load balancing (LB) is triggered; with
HAVE_RT_PUSH_IPI enabled, they send IPIs to CPU0 to drive the execution
of rto_push_irq_work_func. During push_rt_task on CPU0,
if next_task->prio < rq->donor->prio, resched_curr() sets NEED_RESCHED
and after the push operation completes, CPU0 calls rto_next_cpu().
Since only CPU0 is overloaded in this scenario, rto_next_cpu() should
ideally return -1 (no further IPI needed).
However, multiple CPUs invoking tell_cpu_to_push() during LB increments
rd->rto_loop_next. Even when rd->rto_cpu is set to -1, the mismatch between
rd->rto_loop and rd->rto_loop_next forces rto_next_cpu() to restart its
search from -1. With CPU0 remaining overloaded (satisfying rt_nr_migratory
&& rt_nr_total > 1), it gets reselected, causing CPU0 to queue irq_work to
itself and send self-IPIs repeatedly. As long as CPU0 stays overloaded and
other CPUs run pull_rt_tasks(), it falls into an infinite self-IPI loop,
which triggers a CPU hardlockup due to continuous self-interrupts.
The trigging scenario is as follows:
cpu0 cpu1 cpu2
pull_rt_task
tell_cpu_to_push
<------------irq_work_queue_on
rto_push_irq_work_func
push_rt_task
resched_curr(rq) pull_rt_task
rto_next_cpu tell_cpu_to_push
<-------------------------- atomic_inc(rto_loop_next)
rd->rto_loop != next
rto_next_cpu
irq_work_queue_on
rto_push_irq_work_func
Fix redundant self-IPI by filtering the initiating CPU in rto_next_cpu().
This solution has been verified to effectively eliminate spurious self-IPIs
and prevent CPU hardlockup scenarios.
In the Linux kernel, the following vulnerability has been resolved:
ovpn: tcp - don't deref NULL sk_socket member after tcp_close()
When deleting a peer in case of keepalive expiration, the peer is
removed from the OpenVPN hashtable and is temporary inserted in a
"release list" for further processing.
This happens in:
ovpn_peer_keepalive_work()
unlock_ovpn(release_list)
This processing includes detaching from the socket being used to
talk to this peer, by restoring its original proto and socket
ops/callbacks.
In case of TCP it may happen that, while the peer is sitting in
the release list, userspace decides to close the socket.
This will result in a concurrent execution of:
tcp_close(sk)
__tcp_close(sk)
sock_orphan(sk)
sk_set_socket(sk, NULL)
The last function call will set sk->sk_socket to NULL.
When the releasing routine is resumed, ovpn_tcp_socket_detach()
will attempt to dereference sk->sk_socket to restore its original
ops member. This operation will crash due to sk->sk_socket being NULL.
Fix this race condition by testing-and-accessing
sk->sk_socket atomically under sk->sk_callback_lock.
In the Linux kernel, the following vulnerability has been resolved:
ipvs: do not keep dest_dst if dev is going down
There is race between the netdev notifier ip_vs_dst_event()
and the code that caches dst with dev that is going down.
As the FIB can be notified for the closed device after our
handler finishes, it is possible valid route to be returned
and cached resuling in a leaked dev reference until the dest
is not removed.
To prevent new dest_dst to be attached to dest just after the
handler dropped the old one, add a netif_running() check
to make sure the notifier handler is not currently running
for device that is closing.
In the Linux kernel, the following vulnerability has been resolved:
power: supply: sbs-battery: Fix use-after-free in power_supply_changed()
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle. Keep the old behavior of
just printing a warning in case of any failures during the IRQ request
and finishing the probe successfully.
In the Linux kernel, the following vulnerability has been resolved:
fat: avoid parent link count underflow in rmdir
Corrupted FAT images can leave a directory inode with an incorrect
i_nlink (e.g. 2 even though subdirectories exist). rmdir then
unconditionally calls drop_nlink(dir) and can drive i_nlink to 0,
triggering the WARN_ON in drop_nlink().
Add a sanity check in vfat_rmdir() and msdos_rmdir(): only drop the
parent link count when it is at least 3, otherwise report a filesystem
error.
In the Linux kernel, the following vulnerability has been resolved:
Revert "hwmon: (ibmpex) fix use-after-free in high/low store"
This reverts commit 6946c726c3f4c36f0f049e6f97e88c510b15f65d.
Jean Delvare points out that the patch does not completely
fix the reported problem, that it in fact introduces a
(new) race condition, and that it may actually not be needed in
the first place.
Various AI reviews agree. Specific and relevant AI feedback:
"
This reordering sets the driver data to NULL before removing the sensor
attributes in the loop below.
ibmpex_show_sensor() retrieves this driver data via dev_get_drvdata() but
does not check if it is NULL before dereferencing it to access
data->sensors[].
If a userspace process reads a sensor file (like temp1_input) while this
delete function is running, could it race with the dev_set_drvdata(...,
NULL) call here and crash in ibmpex_show_sensor()?
Would it be safer to keep the original order where device_remove_file() is
called before clearing the driver data? device_remove_file() should wait
for any active sysfs callbacks to complete, which might already prevent the
use-after-free this patch intends to fix.
"
Revert the offending patch. If it can be shown that the originally reported
alleged race condition does indeed exist, it can always be re-introduced
with a complete fix.
In the Linux kernel, the following vulnerability has been resolved:
net: bridge: mcast: always update mdb_n_entries for vlan contexts
syzbot triggered a warning[1] about the number of mdb entries in a context.
It turned out that there are multiple ways to trigger that warning today
(some got added during the years), the root cause of the problem is that
the increase is done conditionally, and over the years these different
conditions increased so there were new ways to trigger the warning, that is
to do a decrease which wasn't paired with a previous increase.
For example one way to trigger it is with flush:
$ ip l add br0 up type bridge vlan_filtering 1 mcast_snooping 1
$ ip l add dumdum up master br0 type dummy
$ bridge mdb add dev br0 port dumdum grp 239.0.0.1 permanent vid 1
$ ip link set dev br0 down
$ ip link set dev br0 type bridge mcast_vlan_snooping 1
^^^^ this will enable snooping, but will not update mdb_n_entries
because in __br_multicast_enable_port_ctx() we check !netif_running
$ bridge mdb flush dev br0
^^^ this will trigger the warning because it will delete the pg which
we added above, which will try to decrease mdb_n_entries
Fix the problem by removing the conditional increase and always keep the
count up-to-date while the vlan exists. In order to do that we have to
first initialize it on port-vlan context creation, and then always increase
or decrease the value regardless of mcast options. To keep the current
behaviour we have to enforce the mdb limit only if the context is port's or
if the port-vlan's mcast snooping is enabled.
[1]
------------[ cut here ]------------
n == 0
WARNING: net/bridge/br_multicast.c:718 at br_multicast_port_ngroups_dec_one net/bridge/br_multicast.c:718 [inline], CPU#0: syz.4.4607/22043
WARNING: net/bridge/br_multicast.c:718 at br_multicast_port_ngroups_dec net/bridge/br_multicast.c:771 [inline], CPU#0: syz.4.4607/22043
WARNING: net/bridge/br_multicast.c:718 at br_multicast_del_pg+0x1bbe/0x1e20 net/bridge/br_multicast.c:825, CPU#0: syz.4.4607/22043
Modules linked in:
CPU: 0 UID: 0 PID: 22043 Comm: syz.4.4607 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/24/2026
RIP: 0010:br_multicast_port_ngroups_dec_one net/bridge/br_multicast.c:718 [inline]
RIP: 0010:br_multicast_port_ngroups_dec net/bridge/br_multicast.c:771 [inline]
RIP: 0010:br_multicast_del_pg+0x1bbe/0x1e20 net/bridge/br_multicast.c:825
Code: 41 5f 5d e9 04 7a 48 f7 e8 3f 73 5c f7 90 0f 0b 90 e9 cf fd ff ff e8 31 73 5c f7 90 0f 0b 90 e9 16 fd ff ff e8 23 73 5c f7 90 <0f> 0b 90 e9 60 fd ff ff e8 15 73 5c f7 eb 05 e8 0e 73 5c f7 48 8b
RSP: 0018:ffffc9000c207220 EFLAGS: 00010293
RAX: ffffffff8a68042d RBX: ffff88807c6f1800 RCX: ffff888066e90000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: 0000000000000000 R08: ffff888066e90000 R09: 000000000000000c
R10: 000000000000000c R11: 0000000000000000 R12: ffff8880303ef800
R13: dffffc0000000000 R14: ffff888050eb11c4 R15: 1ffff1100a1d6238
FS: 00007fa45921b6c0(0000) GS:ffff8881256f5000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa4591f9ff8 CR3: 0000000081df2000 CR4: 00000000003526f0
Call Trace:
<TASK>
br_mdb_flush_pgs net/bridge/br_mdb.c:1525 [inline]
br_mdb_flush net/bridge/br_mdb.c:1544 [inline]
br_mdb_del_bulk+0x5e2/0xb20 net/bridge/br_mdb.c:1561
rtnl_mdb_del+0x48a/0x640 net/core/rtnetlink.c:-1
rtnetlink_rcv_msg+0x77e/0xbe0 net/core/rtnetlink.c:6967
netlink_rcv_skb+0x232/0x4b0 net/netlink/af_netlink.c:2550
netlink_unicast_kernel net/netlink/af_netlink.c:1318 [inline]
netlink_unicast+0x80f/0x9b0 net/netlink/af_netlink.c:1344
netlink_sendmsg+0x813/0xb40 net/netlink/af_netlink.c:1894
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg net/socket.c:742 [inline]
____sys_sendmsg+0xa68/0xad0 net/socket.c:2592
___sys_sendmsg+0x2a5/0x360 net/socke
---truncated---
In the Linux kernel, the following vulnerability has been resolved:
ext4: don't cache extent during splitting extent
Caching extents during the splitting process is risky, as it may result
in stale extents remaining in the status tree. Moreover, in most cases,
the corresponding extent block entries are likely already cached before
the split happens, making caching here not particularly useful.
Assume we have an unwritten extent, and then DIO writes the first half.
[UUUUUUUUUUUUUUUU] on-disk extent U: unwritten extent
[UUUUUUUUUUUUUUUU] extent status tree
|<- ->| ----> dio write this range
First, when ext4_split_extent_at() splits this extent, it truncates the
existing extent and then inserts a new one. During this process, this
extent status entry may be shrunk, and calls to ext4_find_extent() and
ext4_cache_extents() may occur, which could potentially insert the
truncated range as a hole into the extent status tree. After the split
is completed, this hole is not replaced with the correct status.
[UUUUUUU|UUUUUUUU] on-disk extent U: unwritten extent
[UUUUUUU|HHHHHHHH] extent status tree H: hole
Then, the outer calling functions will not correct this remaining hole
extent either. Finally, if we perform a delayed buffer write on this
latter part, it will re-insert the delayed extent and cause an error in
space accounting.
In adition, if the unwritten extent cache is not shrunk during the
splitting, ext4_cache_extents() also conflicts with existing extents
when caching extents. In the future, we will add checks when caching
extents, which will trigger a warning. Therefore, Do not cache extents
that are being split.
In the Linux kernel, the following vulnerability has been resolved:
usb: cdns3: fix role switching during resume
If the role change while we are suspended, the cdns3 driver switches to the
new mode during resume. However, switching to host mode in this context
causes a NULL pointer dereference.
The host role's start() operation registers a xhci-hcd device, but its
probe is deferred while we are in the resume path. The host role's resume()
operation assumes the xhci-hcd device is already probed, which is not the
case, leading to the dereference. Since the start() operation of the new
role is already called, the resume operation can be skipped.
So skip the resume operation for the new role if a role switch occurs
during resume. Once the resume sequence is complete, the xhci-hcd device
can be probed in case of host mode.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000208
Mem abort info:
...
Data abort info:
...
[0000000000000208] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 0000000096000004 [#1] SMP
Modules linked in:
CPU: 0 UID: 0 PID: 146 Comm: sh Not tainted
6.19.0-rc7-00013-g6e64f4aabfae-dirty #135 PREEMPT
Hardware name: Texas Instruments J7200 EVM (DT)
pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : usb_hcd_is_primary_hcd+0x0/0x1c
lr : cdns_host_resume+0x24/0x5c
...
Call trace:
usb_hcd_is_primary_hcd+0x0/0x1c (P)
cdns_resume+0x6c/0xbc
cdns3_controller_resume.isra.0+0xe8/0x17c
cdns3_plat_resume+0x18/0x24
platform_pm_resume+0x2c/0x68
dpm_run_callback+0x90/0x248
device_resume+0x100/0x24c
dpm_resume+0x190/0x2ec
dpm_resume_end+0x18/0x34
suspend_devices_and_enter+0x2b0/0xa44
pm_suspend+0x16c/0x5fc
state_store+0x80/0xec
kobj_attr_store+0x18/0x2c
sysfs_kf_write+0x7c/0x94
kernfs_fop_write_iter+0x130/0x1dc
vfs_write+0x240/0x370
ksys_write+0x70/0x108
__arm64_sys_write+0x1c/0x28
invoke_syscall+0x48/0x10c
el0_svc_common.constprop.0+0x40/0xe0
do_el0_svc+0x1c/0x28
el0_svc+0x34/0x108
el0t_64_sync_handler+0xa0/0xe4
el0t_64_sync+0x198/0x19c
Code: 52800003 f9407ca5 d63f00a0 17ffffe4 (f9410401)
---[ end trace 0000000000000000 ]---
In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Fix race condition in QP timer handlers
I encontered the following warning:
WARNING: drivers/infiniband/sw/rxe/rxe_task.c:249 at rxe_sched_task+0x1c8/0x238 [rdma_rxe], CPU#0: swapper/0/0
...
libsha1 [last unloaded: ip6_udp_tunnel]
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Tainted: G C 6.19.0-rc5-64k-v8+ #37 PREEMPT
Tainted: [C]=CRAP
Hardware name: Raspberry Pi 4 Model B Rev 1.2
Call trace:
rxe_sched_task+0x1c8/0x238 [rdma_rxe] (P)
retransmit_timer+0x130/0x188 [rdma_rxe]
call_timer_fn+0x68/0x4d0
__run_timers+0x630/0x888
...
WARNING: drivers/infiniband/sw/rxe/rxe_task.c:38 at rxe_sched_task+0x1c0/0x238 [rdma_rxe], CPU#0: swapper/0/0
...
WARNING: drivers/infiniband/sw/rxe/rxe_task.c:111 at do_work+0x488/0x5c8 [rdma_rxe], CPU#3: kworker/u17:4/93400
...
refcount_t: underflow; use-after-free.
WARNING: lib/refcount.c:28 at refcount_warn_saturate+0x138/0x1a0, CPU#3: kworker/u17:4/93400
The issue is caused by a race condition between retransmit_timer() and
rxe_destroy_qp, leading to the Queue Pair's (QP) reference count dropping
to zero during timer handler execution.
It seems this warning is harmless because rxe_qp_do_cleanup() will flush
all pending timers and requests.
Example of flow causing the issue:
CPU0 CPU1
retransmit_timer() {
spin_lock_irqsave
rxe_destroy_qp()
__rxe_cleanup()
__rxe_put() // qp->ref_count decrease to 0
rxe_qp_do_cleanup() {
if (qp->valid) {
rxe_sched_task() {
WARN_ON(rxe_read(task->qp) <= 0);
}
}
spin_unlock_irqrestore
}
spin_lock_irqsave
qp->valid = 0
spin_unlock_irqrestore
}
Ensure the QP's reference count is maintained and its validity is checked
within the timer callbacks by adding calls to rxe_get(qp) and corresponding
rxe_put(qp) after use.
In the Linux kernel, the following vulnerability has been resolved:
clk: mediatek: Drop __initconst from gates
Since commit 8ceff24a754a ("clk: mediatek: clk-gate: Refactor
mtk_clk_register_gate to use mtk_gate struct") the mtk_gate structs
are no longer just used for initialization/registration, but also at
runtime. So drop __initconst annotations.
In the Linux kernel, the following vulnerability has been resolved:
accel/amdxdna: Fix memory leak in amdxdna_ubuf_map
The amdxdna_ubuf_map() function allocates memory for sg and
internal sg table structures, but it fails to free them if subsequent
operations (sg_alloc_table_from_pages or dma_map_sgtable) fail.
In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Fix deadlocks between devlink and netdev instance locks
In the mentioned "Fixes" commit, various work tasks triggering devlink
health reporter recovery were switched to use netdev_trylock to protect
against concurrent tear down of the channels being recovered. But this
had the side effect of introducing potential deadlocks because of
incorrect lock ordering.
The correct lock order is described by the init flow:
probe_one -> mlx5_init_one (acquires devlink lock)
-> mlx5_init_one_devl_locked -> mlx5_register_device
-> mlx5_rescan_drivers_locked -...-> mlx5e_probe -> _mlx5e_probe
-> register_netdev (acquires rtnl lock)
-> register_netdevice (acquires netdev lock)
=> devlink lock -> rtnl lock -> netdev lock.
But in the current recovery flow, the order is wrong:
mlx5e_tx_err_cqe_work (acquires netdev lock)
-> mlx5e_reporter_tx_err_cqe -> mlx5e_health_report
-> devlink_health_report (acquires devlink lock => boom!)
-> devlink_health_reporter_recover
-> mlx5e_tx_reporter_recover -> mlx5e_tx_reporter_recover_from_ctx
-> mlx5e_tx_reporter_err_cqe_recover
The same pattern exists in:
mlx5e_reporter_rx_timeout
mlx5e_reporter_tx_ptpsq_unhealthy
mlx5e_reporter_tx_timeout
Fix these by moving the netdev_trylock calls from the work handlers
lower in the call stack, in the respective recovery functions, where
they are actually necessary.
In the Linux kernel, the following vulnerability has been resolved:
power: supply: pf1550: Fix use-after-free in power_supply_changed()
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle.
In the Linux kernel, the following vulnerability has been resolved:
xfrm: fix ip_rt_bug race in icmp_route_lookup reverse path
icmp_route_lookup() performs multiple route lookups to find a suitable
route for sending ICMP error messages, with special handling for XFRM
(IPsec) policies.
The lookup sequence is:
1. First, lookup output route for ICMP reply (dst = original src)
2. Pass through xfrm_lookup() for policy check
3. If blocked (-EPERM) or dst is not local, enter "reverse path"
4. In reverse path, call xfrm_decode_session_reverse() to get fl4_dec
which reverses the original packet's flow (saddr<->daddr swapped)
5. If fl4_dec.saddr is local (we are the original destination), use
__ip_route_output_key() for output route lookup
6. If fl4_dec.saddr is NOT local (we are a forwarding node), use
ip_route_input() to simulate the reverse packet's input path
7. Finally, pass rt2 through xfrm_lookup() with XFRM_LOOKUP_ICMP flag
The bug occurs in step 6: ip_route_input() is called with fl4_dec.daddr
(original packet's source) as destination. If this address becomes local
between the initial check and ip_route_input() call (e.g., due to
concurrent "ip addr add"), ip_route_input() returns a LOCAL route with
dst.output set to ip_rt_bug.
This route is then used for ICMP output, causing dst_output() to call
ip_rt_bug(), triggering a WARN_ON:
------------[ cut here ]------------
WARNING: net/ipv4/route.c:1275 at ip_rt_bug+0x21/0x30, CPU#1
Call Trace:
<TASK>
ip_push_pending_frames+0x202/0x240
icmp_push_reply+0x30d/0x430
__icmp_send+0x1149/0x24f0
ip_options_compile+0xa2/0xd0
ip_rcv_finish_core+0x829/0x1950
ip_rcv+0x2d7/0x420
__netif_receive_skb_one_core+0x185/0x1f0
netif_receive_skb+0x90/0x450
tun_get_user+0x3413/0x3fb0
tun_chr_write_iter+0xe4/0x220
...
Fix this by checking rt2->rt_type after ip_route_input(). If it's
RTN_LOCAL, the route cannot be used for output, so treat it as an error.
The reproducer requires kernel modification to widen the race window,
making it unsuitable as a selftest. It is available at:
https://gist.github.com/mrpre/eae853b72ac6a750f5d45d64ddac1e81
In the Linux kernel, the following vulnerability has been resolved:
powerpc/eeh: fix recursive pci_lock_rescan_remove locking in EEH event handling
The recent commit 1010b4c012b0 ("powerpc/eeh: Make EEH driver device
hotplug safe") restructured the EEH driver to improve synchronization
with the PCI hotplug layer.
However, it inadvertently moved pci_lock_rescan_remove() outside its
intended scope in eeh_handle_normal_event(), leading to broken PCI
error reporting and improper EEH event triggering. Specifically,
eeh_handle_normal_event() acquired pci_lock_rescan_remove() before
calling eeh_pe_bus_get(), but eeh_pe_bus_get() itself attempts to
acquire the same lock internally, causing nested locking and disrupting
normal EEH event handling paths.
This patch adds a boolean parameter do_lock to _eeh_pe_bus_get(),
with two public wrappers:
eeh_pe_bus_get() with locking enabled.
eeh_pe_bus_get_nolock() that skips locking.
Callers that already hold pci_lock_rescan_remove() now use
eeh_pe_bus_get_nolock() to avoid recursive lock acquisition.
Additionally, pci_lock_rescan_remove() calls are restored to the correct
position—after eeh_pe_bus_get() and immediately before iterating affected
PEs and devices. This ensures EEH-triggered PCI removes occur under proper
bus rescan locking without recursive lock contention.
The eeh_pe_loc_get() function has been split into two functions:
eeh_pe_loc_get(struct eeh_pe *pe) which retrieves the loc for given PE.
eeh_pe_loc_get_bus(struct pci_bus *bus) which retrieves the location
code for given bus.
This resolves lockdep warnings such as:
<snip>
[ 84.964298] [ T928] ============================================
[ 84.964304] [ T928] WARNING: possible recursive locking detected
[ 84.964311] [ T928] 6.18.0-rc3 #51 Not tainted
[ 84.964315] [ T928] --------------------------------------------
[ 84.964320] [ T928] eehd/928 is trying to acquire lock:
[ 84.964324] [ T928] c000000003b29d58 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_lock_rescan_remove+0x28/0x40
[ 84.964342] [ T928]
but task is already holding lock:
[ 84.964347] [ T928] c000000003b29d58 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_lock_rescan_remove+0x28/0x40
[ 84.964357] [ T928]
other info that might help us debug this:
[ 84.964363] [ T928] Possible unsafe locking scenario:
[ 84.964367] [ T928] CPU0
[ 84.964370] [ T928] ----
[ 84.964373] [ T928] lock(pci_rescan_remove_lock);
[ 84.964378] [ T928] lock(pci_rescan_remove_lock);
[ 84.964383] [ T928]
*** DEADLOCK ***
[ 84.964388] [ T928] May be due to missing lock nesting notation
[ 84.964393] [ T928] 1 lock held by eehd/928:
[ 84.964397] [ T928] #0: c000000003b29d58 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_lock_rescan_remove+0x28/0x40
[ 84.964408] [ T928]
stack backtrace:
[ 84.964414] [ T928] CPU: 2 UID: 0 PID: 928 Comm: eehd Not tainted 6.18.0-rc3 #51 VOLUNTARY
[ 84.964417] [ T928] Hardware name: IBM,9080-HEX POWER10 (architected) 0x800200 0xf000006 of:IBM,FW1060.00 (NH1060_022) hv:phyp pSeries
[ 84.964419] [ T928] Call Trace:
[ 84.964420] [ T928] [c0000011a7157990] [c000000001705de4] dump_stack_lvl+0xc8/0x130 (unreliable)
[ 84.964424] [ T928] [c0000011a71579d0] [c0000000002f66e0] print_deadlock_bug+0x430/0x440
[ 84.964428] [ T928] [c0000011a7157a70] [c0000000002fd0c0] __lock_acquire+0x1530/0x2d80
[ 84.964431] [ T928] [c0000011a7157ba0] [c0000000002fea54] lock_acquire+0x144/0x410
[ 84.964433] [ T928] [c0000011a7157cb0] [c0000011a7157cb0] __mutex_lock+0xf4/0x1050
[ 84.964436] [ T928] [c0000011a7157e00] [c000000000de21d8] pci_lock_rescan_remove+0x28/0x40
[ 84.964439] [ T928] [c0000011a7157e20] [c00000000004ed98] eeh_pe_bus_get+0x48/0xc0
[ 84.964442] [ T928] [c0000011a7157e50] [c00000
---truncated---
In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix memory access flags in helper prototypes
After commit 37cce22dbd51 ("bpf: verifier: Refactor helper access type tracking"),
the verifier started relying on the access type flags in helper
function prototypes to perform memory access optimizations.
Currently, several helper functions utilizing ARG_PTR_TO_MEM lack the
corresponding MEM_RDONLY or MEM_WRITE flags. This omission causes the
verifier to incorrectly assume that the buffer contents are unchanged
across the helper call. Consequently, the verifier may optimize away
subsequent reads based on this wrong assumption, leading to correctness
issues.
For bpf_get_stack_proto_raw_tp, the original MEM_RDONLY was incorrect
since the helper writes to the buffer. Change it to ARG_PTR_TO_UNINIT_MEM
which correctly indicates write access to potentially uninitialized memory.
Similar issues were recently addressed for specific helpers in commit
ac44dcc788b9 ("bpf: Fix verifier assumptions of bpf_d_path's output buffer")
and commit 2eb7648558a7 ("bpf: Specify access type of bpf_sysctl_get_name args").
Fix these prototypes by adding the correct memory access flags.
In the Linux kernel, the following vulnerability has been resolved:
power: supply: bq256xx: Fix use-after-free in power_supply_changed()
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle.
In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: revert commit_mutex usage in reset path
It causes circular lock dependency between commit_mutex, nfnl_subsys_ipset
and nlk_cb_mutex when nft reset, ipset list, and iptables-nft with '-m set'
rule run at the same time.
Previous patches made it safe to run individual reset handlers concurrently
so commit_mutex is no longer required to prevent this.
In the Linux kernel, the following vulnerability has been resolved:
crypto: caam - fix netdev memory leak in dpaa2_caam_probe
When commit 0e1a4d427f58 ("crypto: caam: Unembed net_dev structure in
dpaa2") converted embedded net_device to dynamically allocated pointers,
it added cleanup in dpaa2_dpseci_disable() but missed adding cleanup in
dpaa2_dpseci_free() for error paths.
This causes memory leaks when dpaa2_dpseci_dpio_setup() fails during probe
due to DPIO devices not being ready yet. The kernel's deferred probe
mechanism handles the retry successfully, but the netdevs allocated during
the failed probe attempt are never freed, resulting in kmemleak reports
showing multiple leaked netdev-related allocations all traced back to
dpaa2_caam_probe().
Fix this by preserving the CPU mask of allocated netdevs during setup and
using it for cleanup in dpaa2_dpseci_free(). This approach ensures that
only the CPUs that actually had netdevs allocated will be cleaned up,
avoiding potential issues with CPU hotplug scenarios.
In the Linux kernel, the following vulnerability has been resolved:
ext4: drop extent cache when splitting extent fails
When the split extent fails, we might leave some extents still being
processed and return an error directly, which will result in stale
extent entries remaining in the extent status tree. So drop all of the
remaining potentially stale extents if the splitting fails.
In the Linux kernel, the following vulnerability has been resolved:
RDMA/iwcm: Fix workqueue list corruption by removing work_list
The commit e1168f0 ("RDMA/iwcm: Simplify cm_event_handler()")
changed the work submission logic to unconditionally call
queue_work() with the expectation that queue_work() would
have no effect if work was already pending. The problem is
that a free list of struct iwcm_work is used (for which
struct work_struct is embedded), so each call to queue_work()
is basically unique and therefore does indeed queue the work.
This causes a problem in the work handler which walks the work_list
until it's empty to process entries. This means that a single
run of the work handler could process item N+1 and release it
back to the free list while the actual workqueue entry is still
queued. It could then get reused (INIT_WORK...) and lead to
list corruption in the workqueue logic.
Fix this by just removing the work_list. The workqueue already
does this for us.
This fixes the following error that was observed when stress
testing with ucmatose on an Intel E830 in iWARP mode:
[ 151.465780] list_del corruption. next->prev should be ffff9f0915c69c08, but was ffff9f0a1116be08. (next=ffff9f0a15b11c08)
[ 151.466639] ------------[ cut here ]------------
[ 151.466986] kernel BUG at lib/list_debug.c:67!
[ 151.467349] Oops: invalid opcode: 0000 [#1] SMP NOPTI
[ 151.467753] CPU: 14 UID: 0 PID: 2306 Comm: kworker/u64:18 Not tainted 6.19.0-rc4+ #1 PREEMPT(voluntary)
[ 151.468466] Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[ 151.469192] Workqueue: 0x0 (iw_cm_wq)
[ 151.469478] RIP: 0010:__list_del_entry_valid_or_report+0xf0/0x100
[ 151.469942] Code: c7 58 5f 4c b2 e8 10 50 aa ff 0f 0b 48 89 ef e8 36 57 cb ff 48 8b 55 08 48 89 e9 48 89 de 48 c7 c7 a8 5f 4c b2 e8 f0 4f aa ff <0f> 0b 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 90 90 90 90 90 90
[ 151.471323] RSP: 0000:ffffb15644e7bd68 EFLAGS: 00010046
[ 151.471712] RAX: 000000000000006d RBX: ffff9f0915c69c08 RCX: 0000000000000027
[ 151.472243] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9f0a37d9c600
[ 151.472768] RBP: ffff9f0a15b11c08 R08: 0000000000000000 R09: c0000000ffff7fff
[ 151.473294] R10: 0000000000000001 R11: ffffb15644e7bba8 R12: ffff9f092339ee68
[ 151.473817] R13: ffff9f0900059c28 R14: ffff9f092339ee78 R15: 0000000000000000
[ 151.474344] FS: 0000000000000000(0000) GS:ffff9f0a847b5000(0000) knlGS:0000000000000000
[ 151.474934] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 151.475362] CR2: 0000559e233a9088 CR3: 000000020296b004 CR4: 0000000000770ef0
[ 151.475895] PKRU: 55555554
[ 151.476118] Call Trace:
[ 151.476331] <TASK>
[ 151.476497] move_linked_works+0x49/0xa0
[ 151.476792] __pwq_activate_work.isra.46+0x2f/0xa0
[ 151.477151] pwq_dec_nr_in_flight+0x1e0/0x2f0
[ 151.477479] process_scheduled_works+0x1c8/0x410
[ 151.477823] worker_thread+0x125/0x260
[ 151.478108] ? __pfx_worker_thread+0x10/0x10
[ 151.478430] kthread+0xfe/0x240
[ 151.478671] ? __pfx_kthread+0x10/0x10
[ 151.478955] ? __pfx_kthread+0x10/0x10
[ 151.479240] ret_from_fork+0x208/0x270
[ 151.479523] ? __pfx_kthread+0x10/0x10
[ 151.479806] ret_from_fork_asm+0x1a/0x30
[ 151.480103] </TASK>
In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_counter: serialize reset with spinlock
Add a global static spinlock to serialize counter fetch+reset
operations, preventing concurrent dump-and-reset from underrunning
values.
The lock is taken before fetching the total so that two parallel
resets cannot both read the same counter values and then both
subtract them.
A global lock is used for simplicity since resets are infrequent.
If this becomes a bottleneck, it can be replaced with a per-net
lock later.
In the Linux kernel, the following vulnerability has been resolved:
mtd: intel-dg: Fix accessing regions before setting nregions
The regions array is counted by nregions, but it's set only after
accessing it:
[] UBSAN: array-index-out-of-bounds in drivers/mtd/devices/mtd_intel_dg.c:750:15
[] index 0 is out of range for type '<unknown> [*]'
Fix it by also fixing an undesired behavior: the loop silently ignores
ENOMEM and continues setting the other entries.
In the Linux kernel, the following vulnerability has been resolved:
quota: fix livelock between quotactl and freeze_super
When a filesystem is frozen, quotactl_block() enters a retry loop
waiting for the filesystem to thaw. It acquires s_umount, checks the
freeze state, drops s_umount and uses sb_start_write() - sb_end_write()
pair to wait for the unfreeze.
However, this retry loop can trigger a livelock issue, specifically on
kernels with preemption disabled.
The mechanism is as follows:
1. freeze_super() sets SB_FREEZE_WRITE and calls sb_wait_write().
2. sb_wait_write() calls percpu_down_write(), which initiates
synchronize_rcu().
3. Simultaneously, quotactl_block() spins in its retry loop, immediately
executing the sb_start_write() - sb_end_write() pair.
4. Because the kernel is non-preemptible and the loop contains no
scheduling points, quotactl_block() never yields the CPU. This
prevents that CPU from reaching an RCU quiescent state.
5. synchronize_rcu() in the freezer thread waits indefinitely for the
quotactl_block() CPU to report a quiescent state.
6. quotactl_block() spins indefinitely waiting for the freezer to
advance, which it cannot do as it is blocked on the RCU sync.
This results in a hang of the freezer process and 100% CPU usage by the
quota process.
While this can occur intermittently on multi-core systems, it is
reliably reproducing on a node with the following script, running both
the freezer and the quota toggle on the same CPU:
# mkfs.ext4 -O quota /dev/sda 2g && mkdir a_mount
# mount /dev/sda -o quota,usrquota,grpquota a_mount
# taskset -c 3 bash -c "while true; do xfs_freeze -f a_mount; \
xfs_freeze -u a_mount; done" &
# taskset -c 3 bash -c "while true; do quotaon a_mount; \
quotaoff a_mount; done" &
Adding cond_resched() to the retry loop fixes the issue. It acts as an
RCU quiescent state, allowing synchronize_rcu() in percpu_down_write()
to complete.